| |
| Paint Application » General Painting Strategies » Rag Rolling » Glazing » Sponging |
| |
Paint Application Tips |
| Applying paint can be done in a number of ways. From traditional brush/roller application to the more modern methods, understanding the correct techniques for applying paint is important. Knowing the different methods of application allows you to choose the best style for your situation. |
| |
Top to Bottom
Whether you're a pro or novice, starting at the top gives you a chance to fix those little goofs and other mishaps as you work your way down.
Do Edges First
Edges should be cut around doors and windows, above baseboards and at the line where the ceiling meets the wall. Cutting the edges involves outlining the area to be painted with a 2 1/2" angled-bristle brush and is a crucial step in "framing the canvas." From there, a roller can be used for most of the rest of the job.
|
 |
|
Using a Roller
When painting with a roller, it's important to work in three to four foot square sections to make the job more manageable. This also works as a guide for "roller loading" - a roller should not be reloaded until the section has been finished.
Work in a zigzag pattern: A "W" should be painted on the surface from top to bottom and left to right. From there, the section should be filled with horizontal strokes. To finish off, the section should be smoothed with all-vertical strokes - this will maintain the same "pattern" and help to fuse the smaller sections into one finished surface when the paint is dry.
For complete coverage, two coats are almost always recommended. |
| |
| Back to the Top |
Here you simply apply one or more transparent glazes over a dry base coat. Then you use almost any household tool or material to remove some of the glaze while it's still wet. The result is an almost unlimited range of depth of color, pattern and texture. This truly brings out the artist in you, because you can produce virtually any visual effect you can imagine.
|
Paint Needed:
- Base Coat: Ace Royal Touch Semi-Gloss or Satin Latex Wall Paint
- Roll Coat(s):
1 part Ace Royal Touch Satin Latex Wall Paint (tinted to desired color);
3 parts Ace Great Finishes Latex Acrylic Satin Polyurethane (thin with polyurethane as needed)
|
Just follow these simple directions:
- Mask off areas not to be rolled.
- Roll or brush on base coat. Allow to dry overnight.
- Roll rag into sausage shape.
- Pour first rolling color into tray.
- Dip rag into tray, wring out slightly.
- Starting at the bottom, and with very little pressure, roll the rag up the entire wall without stopping.
- To avoid repetitive pattern, turn rag frequently.
- If paint builds up on rag, either turn it inside out or switch to a fresh rag.
- Avoid lap marks by rolling wall corner to corner without stopping.
- Let dry to the touch. Apply additional colors one at a time. Allow to dry between each coat.
|
|
 |
Helpful Hints and Tips:
- Practice rolling on a sample board until you get a feel for the pressure needed for the effect you want.
- For corners, use the tip of the rag.
- Cut the rags to a width that's comfortable to work with and don't change rag textures in the middle of your work.
Protect your work with a coat of clear Ace Great Finishes Acrylic Polyurethane Satin Finish. |
| |
| Back to the Top |
Here you simply apply one or more transparent glazes over a dry base coat. Then you use almost any household tool or material to remove some of the glaze while it's still wet. The result is an almost unlimited range of depth of color, pattern and texture. Glazing truly brings out the artist in you, because you can produce virtually any visual effect you can imagine.
|
Tools Needed:
- 3/8" short nap roller
- 3" - 8" brush
- Gloves
- Painter's masking tape
- Painter's rags
- Drop cloths
- Various glazing tools (brushes of various sizes are used to create multiple patterns)
|
|  |
Just follow these simple directions:
- Mask off areas not to be glazed
- Roll or brush on base coat. Allow to dry overnight.
- Pour first glazing color into tray.
- Starting in a corner, apply a thin, even coat of glaze with a brush or roller to a width of three to four feet on wall. Remember, the more you apply, the more you'll have to remove.
- Using your technique of choice, remove glaze to create a pattern or texture.
- Avoid lap marks by glazing wall from corner to corner without stopping.
|
Helpful Hints and Tips:
- Practice your technique on a sample board.
- Because the glaze must be removed before it becomes too tacky to work with, glazing is easier with two people. One person applies the glaze, the other removes it. To maintain a uniform look, the same person should always remove the glaze.
- To blend one section of glaze into the next, leave a "wet" edge-a small strip of un-worked glaze at the end of each section.
- If it looks like you will run out of glaze, stop in a corner or other natural break. Do NOT stop in the middle of the wall.
|
| |
| Back to the Top |
Here you simply apply one or more transparent glazes over a dry base coat. Then you use almost any household tool or material to remove some of the glaze while it's still wet. The result is an almost unlimited range of depth of color, pattern and texture. Glazing truly brings out the artist in you, because you can produce virtually any visual effect you can imagine.
|
Paint Needed:
- Base Coat: Ace Royal Touch Semi-Gloss or Satin Latex Wall Paint
- Sponge Coat(s): 1 part Ace Royal Touch Semi-Gloss or Satin Latex Wall Paint; 8 parts Ace Artistic Finishes Latex Glazing Liquid
Tools Needed:
- 3/8" short nap roller
- 2" brush
- Gloves
- Paint trays
- Natural sea sponge
- "Corner" sponge (cut on side to give flat edge)
- Painter's masking tape
- Newspaper
- Drop cloths
- Various glazing tools
|
|  |
|
|
| |
Just follow these simple directions:
- Mask off areas not to be glazed.
- Roll or brush on base coat. Allow to dry overnight.
- Wet sponge with water, wring out until damp.
- Pour first sponging color into tray.
- Lightly dip sponge into tray; remove excess paint by dabbing on newspaper.
- Practice your sponging technique on a sample board until you're satisfied with the results.
- Starting anywhere on the wall, gently dab with sponge in a broad even pattern. Keep dabs equally spaced in 3'x3' area for best results. Then fill in the detail of the pattern for that area.
- Reload sponges and dab in an adjacent area. Continue until wall is covered.
- Sponge corners with corner sponge.
- With a dry 2" brush and a straight-up-and-down motion, soften and fill in corners.
- Let dry to the touch.
- Apply additional colors one at a time.
Helpful Hints and Tips:
- Practice your technique on a sample board.
- Because the glaze must be removed before it becomes too tacky to work with, glazing is easier with two people. One applies the glaze, the other removes it. To maintain a uniform look, the same person should always remove the glaze.
- To blend one section of glaze into the next, leave a "wet" edge-a small strip of unworked glaze at the end of each section.
- If it looks like you will run out of glaze, stop in a corner or other natural break. Do NOT stop in the middle of the wall.
|
| |
| Back to the Top |
Check your state and local codes before starting any project. Follow all safety precautions. Information in this document has been furnished by the North American Retail Hardware Association (NRHA) and associated contributors. Every effort has been made to ensure accuracy and safety. Neither NRHA, any contributor nor the retailer can be held responsible for damages or injuries resulting from the use of the information in this document. |
